![]() ![]() Use recommended measuring instruments or equivalents.- Return the equipment to the original state and check the operation when the service is finished.ģ. When servicing the equipment with the power turned ON, be sure not to touch live sections androtating/operating sections. Be careful when removing the covers since there might be the parts with very sharp edgesunderneath. Make sure that the equipment will not operate before touching potentially dangerous places (e.g.rotating/operating sections such as gears, belts pulleys, fans and laser beam exit of the laser optical unit). on them even after thepower is turned OFF. Especially, the board of these components should notbe touched since the electric charge may remain in the capacitors, etc. Be sure not to touch high-voltage sections such as the chargers, transfer roller, developer, high-voltage transformer and power supply unit. Be sure not to touch high-temperature sections such as the fuser unit, damp heater and areasaround them. Remove all reflecting metals such as watches, rings, etc. Do not insert reflecting parts or tools such as a screwdriver on the laser beam path. Be sure not toexpose your eyes to the laser beam. Avoid expose to laser beam during service. Basically, the equipment should not be operated with any parts removed or disassembled.- The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristbandsince the ICs on it may be damaged due to static electricity. Be careful not to install small parts such asscrews, washers, pins, E-rings, star washers in the wrong places. Noted in this manual or other related documents. A fire may occur when dust lies on this area.- When the parts are disassembled, reassembly is the reverse of disassembly unless otherwise Should be done with the power turned ON).- Unplug the power cable and clean the area around the prongs of the plug and socket outlet onceĪ year or more. General Precautions at Service- Be sure to turn the power OFF and unplug the power cable during service (except for the service Which have been taken off so that the inside of the equipment is not exposed.Ģ. It.- When the equipment is used after the option is removed, be sure to install the parts or the covers Avoid excessive heat, high humidity, dust, vibration andĭirect sunlight.- Provide proper ventilation since the equipment emits a slight amount of ozone.- To insure adequate working space for the copying operation, keep a minimum clearance of 80Ĭm (32) on the left, 80 cm (32) on the right and 10 cm (4) on the rear.- The equipment shall be installed near the socket outlet and shall be accessible.- Be sure to fix and plug in the power cable securely after the installation so that no one trips over the ADU) when transporting the equipment.- Be sure to use a dedicated outlet with AC 120 V / 12 A, 220-240 V / 8A for its power source.- The equipment must be grounded for safety.- Select a suitable place for installation. Be sure not to hold the movable parts or units (e.g. Positions as shown in the figure.The equipment is quite heavy and weighs approximately 27 kg (59.5 lb.), therefore pay fullattention when handling it. Transportation/Installation- When transporting/installing the equipment, employ two persons and be sure to hold the The installation and service shall be done by a qualified servicetechnician.ġ. GENERAL PRECAUTIONS REGARDING THE SERVICE FORe-STUDIO2505F ![]() Under the copyright laws, this manual cannot be reproduced in any form without prior written permissionof TOSHIBA TEC CORPORATION. Other company names and product names in this manual are the trademarks of their respectiveĢ013 TOSHIBA TEC CORPORATION All rights reserved MIFARE is a trademark of Royal Philips Electronics. iCLASS is a trademark of HID Corporation. FLOIL is a registered trademark of Kanto Kasei Ltd. Molykote is a registered trademark of Dow Corning Corporation. Mylar is a registered trademark of DuPont Teijin Films U.S. NOVELL, NetWare, and NDS are trademarks or registered trademarks of Novell, Inc. PostScript is a trademark of Adobe Systems Incorporated. and/or other countries.Īpple, AppleTalk, Macintosh, and Mac are trademarks of Apple Computer, Inc. Microsoft, Windows, Windows XP, Windows Vista, Windows 7, Windows 8 and the brand namesĪnd product names of other Microsoft products are trademarks or registered trademarks of MicrosoftCorporation in the U.S. ![]() The official name of Windows 8 is Microsoft Windows 8 Operating System. The official name of Windows 7 is Microsoft Windows 7 Operating System. The official name of Windows Vista is Microsoft Windows Vista Operating System. Trademarks The official name of Windows XP is Microsoft Windows XP Operating System. Model: DP-2505FPublish Date: June 2013File No. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |